orderin g numbe r : ena1819 bi-cmos lsi for dsc, and cell phone camera modules h-bridge 4-channel motor driver LV8416CB overview the LV8416CB is an h-bridge 4-channel motor driver ic and is able to control 4 modes of forward, reverse, brake and standby. this ic housed in a wafer level package (wlp) is optimum fo r use in a stepping motor driving system for dsc or a camera module of cell phones. functions ? saturation drive h-bridge: 4-channels ? va rious protection circuits (thermal protection, low voltage malfunction protection) specifications absolute maximum ratings at ta = 25 c parameter symbol conditions ratings unit power supply voltage v cc max 6.0 v output peak current i o peak channels 1 to 4, t 10msec, on-duty 20% 600 ma output continuous current i o max channels 1 to 4 400 ma allowable power dissipation pd max mounted on a circuit board* 1000 mw operating temperature topr -30 to +85 c storage temperature tstg -55 to +150 c z specified circuit board : 60mm 60mm 1.7mm, glass epoxy two-layer board. recommended operating conditions at ta = 25 c parameter symbol conditions ratings unit power supply voltage range v cc op 2.5 to 5.5 v logic input voltage range v in 0 to v cc +0.3 v input frequency f in in1 to 8 to 100 khz specifications of any and all sanyo semiconductor co.,l td. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer ' s products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' sproductsor equipment. any and all sanyo semiconductor co.,ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, av equipment, communication device, office equipment, industrial equ ipment etc.). the products mentioned herein shall not be intended for use for any "special application" (medica l equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, t ransportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of re liability and can directly threaten human lives in case of failure or malfunction of the product or may cause har m to human bodies, nor shall they grant any guarantee thereof. if you should intend to use our products for app lications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. if there is n o consultation or inquiry before the intended use, our customer shall be solely responsible for the use. 81110 sy 20100728-s00004 no.a1819-1/5
LV8416CB electrical characteristics at ta = 25c, v cc = 5v ratings parameter symbol conditions min typ max unit standby mode current drain i st in1 to in8 = ?l? 1.0 a i cc 1 v cc =v in 1 = 3 .3v 40 80 160 a v cc current drain i cc 2 v cc =v in 1 = 5 .0v 50 100 200 a v cc low-voltage cutoff voltage vthv cc 2.0 2.25 2.5 v low-voltage hysteresis vo ltage vthhis 100 150 200 mv thermal shutdown temperature tsd design guarantee value * 160 180 200 c thermal hysteresis width tsd design guarantee value * 10 30 50 c input pin iinl v in = 0v, in1 to in8 1.0 a logic pin input current iinh v in = 3.3v, in1 to in8 8.3 16.5 33 a logic input high-level voltage vinh in1 to in8 0.5 v cc v logic input low-level voltage vinl in1 to in8 0.2 v cc v input circuit current consumption i cc in v in = 3.3v, power hit of in1 to in8 *1 30 80 250 a motor driver ronu i o = 100ma, upper on resistance 0.5 0.75 output on-resistance rond i o = 100ma, lower on resistance 0.3 0.55 output leakage current i o leak 1.0 a diode forward voltage vd id = -100ma 0.4 0.75 1.2 v turn-on time ton time of input 50% output 50% *2 0.10 0.50 sec turn-off time toff time of input 50% output 50% 0.15 0.55 sec at the rise time tr time of output 10% 9 0% 0.05 0.20 sec standing fall time tf time of output 90% 1 0% 0.05 0.20 sec *1: the input circuit current consumption in cmos circuit co mposition of the input steps is generated though it is unquestionab le for ic operation when impressing it to v in voltage that is lower than the v cc voltage. *2: time from change edge to change edge ( 0.5vcc) of control input at output level. it doesn't have an enable pin, and as for this ic, either in the input pin begins and the inte rnal logic begins operation of "h igh". therefore, the turn-on time becomes about three microseconds only at the in itial motion work of the input terminal "high". package dimensions unit : mm (typ) 3401 no.a1819-2/5 sanyo : wlp18(2.47x1.27) side view top view side view bottom view 0.245 123456 cba 0.69 max 0.175 1.27 2.47 0.235 0.4 0.235 0.4 pd max - ta 0 0.52 1.0 0.5 1.5 ? 30 90 60 30 0 120 1.00 ambient temperature, ta -- c allowable power dissipation, pd max -- w specified circuit board : 60.0 60.0 1.7mm 3 glass epoxy board
LV8416CB pin assignment out2 out1 v cc out3 in1 in2 out4 in3 in4 out5 in5 in6 out6 in7 in8 gnd out7 out8 out2 out1 v cc out3 in1 in2 out4 in3 in4 out5 in5 in6 out6 in7 in8 gnd out7 out8 top view bottom view 1 2 3 4 5 6 1 2 3 4 5 6 a bc a bc block diagram cpu out4 out3 out2 out1 v cc out8 out7 out6 out5 in1 in2 in3 in4 in5 in6 in7 in8 gnd logic circuit standard voltage low voltage protection circuit overheating protection circuit no.a1819-3/5
LV8416CB pin functions pin no. pin name pin function equivalent circuit b2 c2 b3 c3 b4 c4 b5 c5 in1 in2 in3 in4 in5 in6 in7 in8 control signal input pin control signal input pin control signal input pin control signal input pin control signal input pin control signal input pin control signal input pin control signal input pin v cc gnd b1 a1 a2 a3 a4 a5 b6 c6 out1 out2 out3 out4 out5 out6 out7 out8 motor driver output pin motor driver output pin motor driver output pin motor driver output pin motor driver output pin motor driver output pin motor driver output pin motor driver output pin gnd v cc c1 v cc logic system power supply connection pin a6 gnd signal ground logic input specifications ? c ommon channels 1 to 4 ch1 : in1 to in2, out1 to out2 ch2 : in3 to in4, out3 to out4 ch3 : in5 to in6, out5 to out6 ch4 : in7 to in8, out7 to out8 input output in1 in2 out1 out2 operation mode l l off off standby h l h l cw ( forward) l h l h ccw (rev erse) h h l l brake no.a1819-4/5
LV8416CB ? output stage transistor function v cc on on off off off off on on on on off off (forward) (reverse) (brake) v cc v cc sanyo semiconductor co.,ltd. assumes no responsib ility for equipment failures that result from using products at values that exceed, even momentarily, rate d values (such as maximum ra tings, operating condition ranges, or other parameters) listed in products specif ications of any and all sanyo semiconductor co.,ltd. products described or contained herein. sanyo semiconductor co.,ltd. strives to supply high-qual ity high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. it is possible that these probabilistic failures or malfunction could give rise to acci dents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause dam age to other property. when designing equipment, adopt safety measures so that these kinds of accidents or e vents cannot occur. such measures include but are not limited to protective circuits and error prevention c ircuits for safe design, redundant design, and structural design. upon using the technical information or products descri bed herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of sanyo semiconductor co.,ltd. or any third party. sanyo semiconductor co.,ltd. shall not be liable f or any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. information (including circuit diagr ams and circuit parameters) herein is for example only; it is not guaranteed for volume production. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equi pment, refer to the "delivery specification" for the sanyo semiconductor co.,ltd. product that you intend to use. in the event that any or all sanyo semiconductor c o.,ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities conc erned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any in formation storage or retrieval system, or otherwise, without the prior written consent of sanyo semiconductor co.,ltd. this catalog provides information as of august, 2010. specifications and information herein are subject to change without notice. ps no.a1819-5/5
|
